Minix Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
x minix x
x minixx
CLOSE(2)                   Linux Programmer's Manual                  CLOSE(2)

NAME
       close - close a file descriptor

SYNOPSIS
       #include <unistd.h>

       int close(int fd);

DESCRIPTION
       close()  closes  a  file descriptor, so that it no longer refers to any
       file and may be reused.  Any record locks (see fcntl(2))  held  on  the
       file it was associated with, and owned by the process, are removed (re-
       gardless of the file descriptor that was used to obtain the lock).

       If fd is the last file descriptor referring to the underlying open file
       description  (see open(2)), the resources associated with the open file
       description are freed; if the file descriptor was the last reference to
       a file which has been removed using unlink(2), the file is deleted.

RETURN VALUE
       close()  returns  zero on success.  On error, -1 is returned, and errno
       is set appropriately.

ERRORS
       EBADF  fd isn't a valid open file descriptor.

       EINTR  The close() call was interrupted by a signal; see signal(7).

       EIO    An I/O error occurred.

       ENOSPC, EDQUOT
              On NFS, these errors are not normally reported against the first
              write  which  exceeds  the  available storage space, but instead
              against a subsequent write(2), fsync(2), or close().

       See NOTES for a discussion of why close() should not be  retried  after
       an error.

CONFORMING TO
       POSIX.1-2001, POSIX.1-2008, SVr4, 4.3BSD.

NOTES
       A  successful  close does not guarantee that the data has been success-
       fully saved to disk, as the kernel  uses  the  buffer  cache  to  defer
       writes.   Typically,  filesystems  do  not flush buffers when a file is
       closed.  If you need to be sure that the data is physically  stored  on
       the  underlying  disk, use fsync(2).  (It will depend on the disk hard-
       ware at this point.)

       The close-on-exec file descriptor flag can be used  to  ensure  that  a
       file  descriptor  is  automatically closed upon a successful execve(2);
       see fcntl(2) for details.

       It is probably unwise to close file descriptors while they  may  be  in
       use by system calls in other threads in the same process.  Since a file
       descriptor may be reused, there are some obscure race  conditions  that
       may cause unintended side effects.

   Dealing with error returns from close()
       A  careful  programmer will check the return value of close(), since it
       is quite possible that errors on a previous write(2) operation are  re-
       ported  only  on the final close() that releases the open file descrip-
       tion.  Failing to check the return value when closing a file  may  lead
       to  silent  loss of data.  This can especially be observed with NFS and
       with disk quota.

       Note, however, that a failure return should be used only for diagnostic
       purposes  (i.e.,  a  warning to the application that there may still be
       I/O pending or there may have been failed  I/O)  or  remedial  purposes
       (e.g., writing the file once more or creating a backup).

       Retrying  the  close() after a failure return is the wrong thing to do,
       since this may cause a reused file descriptor from another thread to be
       closed.   This  can  occur because the Linux kernel always releases the
       file descriptor early in the close operation, freeing it for reuse; the
       steps that may return an error, such as flushing data to the filesystem
       or device, occur only later in the close operation.

       Many other implementations similarly always close the  file  descriptor
       (except  in the case of EBADF, meaning that the file descriptor was in-
       valid) even if  they  subsequently  report  an  error  on  return  from
       close().   POSIX.1  is  currently  silent  on this point, but there are
       plans to mandate this behavior in the next major release of  the  stan-
       dard.

       A  careful  programmer  who  wants to know about I/O errors may precede
       close() with a call to fsync(2).

       The EINTR error is a somewhat special case.  Regarding the EINTR error,
       POSIX.1-2013 says:

              If  close()  is interrupted by a signal that is to be caught, it
              shall return -1 with errno set to EINTR and the state of  fildes
              is unspecified.

       This permits the behavior that occurs on Linux and many other implemen-
       tations, where, as with other errors that may be reported  by  close(),
       the  file descriptor is guaranteed to be closed.  However, it also per-
       mits another possibility: that the implementation returns an EINTR  er-
       ror  and  keeps the file descriptor open.  (According to its documenta-
       tion, HP-UX's close() does this.)  The caller must then once  more  use
       close()  to  close the file descriptor, to avoid file descriptor leaks.
       This divergence in implementation behaviors provides a difficult hurdle
       for  portable applications, since on many implementations, close() must
       not be called again after an EINTR error, and on at least one,  close()
       must  be  called  again.  There are plans to address this conundrum for
       the next major release of the POSIX.1 standard.

SEE ALSO
       fcntl(2), fsync(2), open(2), shutdown(2), unlink(2), fclose(3)

COLOPHON
       This page is part of release 5.05 of the Linux  man-pages  project.   A
       description  of  the project, information about reporting bugs, and the
       latest    version    of    this    page,    can     be     found     at
       https://www.kernel.org/doc/man-pages/.

Linux                             2019-10-10                          CLOSE(2)

NAME | SYNOPSIS | DESCRIPTION | RETURN VALUE | ERRORS | CONFORMING TO | NOTES | SEE ALSO | COLOPHON