Minix Man Pages
home | helpx minix x x minixx UMOUNT(8) System Administration UMOUNT(8) NAME umount - unmount file systems SYNOPSIS umount -a [-dflnrv] [-t fstype] [-O option...] umount [-dflnrv] {directory|device}... umount -h|-V DESCRIPTION The umount command detaches the mentioned file system(s) from the file hierarchy. A file system is specified by giving the directory where it has been mounted. Giving the special device on which the file system lives may also work, but is obsolete, mainly because it will fail in case this device was mounted on more than one directory. Note that a file system cannot be unmounted when it is 'busy' - for ex- ample, when there are open files on it, or when some process has its working directory there, or when a swap file on it is in use. The of- fending process could even be umount itself - it opens libc, and libc in its turn may open for example locale files. A lazy unmount avoids this problem, but it may introduce another issues. See --lazy descrip- tion below. OPTIONS -a, --all All of the filesystems described in /proc/self/mountinfo (or in deprecated /etc/mtab) are unmounted, except the proc, devfs, de- vpts, sysfs, rpc_pipefs and nfsd filesystems. This list of the filesystems may be replaced by --types umount option. -A, --all-targets Unmount all mountpoints in the current namespace for the speci- fied filesystem. The filesystem can be specified by one of the mountpoints or the device name (or UUID, etc.). When this op- tion is used together with --recursive, then all nested mounts within the filesystem are recursively unmounted. This option is only supported on systems where /etc/mtab is a symlink to /proc/mounts. -c, --no-canonicalize Do not canonicalize paths. The paths canonicalization is based on stat(2) and readlink(2) system calls. These system calls may hang in some cases (for example on NFS if server is not avail- able). The option has to be used with canonical path to the mount point. For more details about this option see the mount(8) man page. Note that umount does not pass this option to the /sbin/umount.type helpers. -d, --detach-loop When the unmounted device was a loop device, also free this loop device. This option is unnecessary for devices initialized by mount(8), in this case "autoclear" functionality is enabled by default. --fake Causes everything to be done except for the actual system call or umount helper execution; this 'fakes' unmounting the filesys- tem. It can be used to remove entries from the deprecated /etc/mtab that were unmounted earlier with the -n option. -f, --force Force an unmount (in case of an unreachable NFS system). Note that this option does not guarantee that umount command does not hang. It's strongly recommended to use absolute paths without symlinks to avoid unwanted readlink and stat system calls on unreachable NFS in umount. -i, --internal-only Do not call the /sbin/umount.filesystem helper even if it ex- ists. By default such a helper program is called if it exists. -l, --lazy Lazy unmount. Detach the filesystem from the file hierarchy now, and clean up all references to this filesystem as soon as it is not busy anymore. A system reboot would be expected in near future if you're going to use this option for network filesystem or local filesystem with submounts. The recommended use-case for umount -l is to prevent hangs on shutdown due to an unreachable network share where a normal umount will hang due to a downed server or a net- work partition. Remounts of the share will not be possible. -N, --namespace ns Perform umount in namespace specified by ns. ns is either PID of process running in that namespace or special file represent- ing that namespace. umount(8) switches to the namespace when it reads /etc/fstab, writes /etc/mtab (or writes to /run/mount) and calls umount(2) system call, otherwise it runs in the original namespace. It means that the target namespace does not have to contain any li- braries or another requirements necessary to execute umount(2) command. See namespaces(7) for more information. -n, --no-mtab Unmount without writing in /etc/mtab. -O, --test-opts option... Unmount only the filesystems that have the specified option set in /etc/fstab. More than one option may be specified in a comma-separated list. Each option can be prefixed with no to indicate that no action should be taken for this option. -q, --quiet Suppress "not mounted" error messages. -R, --recursive Recursively unmount each specified directory. Recursion for each directory will stop if any unmount operation in the chain fails for any reason. The relationship between mountpoints is determined by /proc/self/mountinfo entries. The filesystem must be specified by mountpoint path; a recursive unmount by device name (or UUID) is unsupported. -r, --read-only When an unmount fails, try to remount the filesystem read-only. -t, --types type... Indicate that the actions should only be taken on filesystems of the specified type. More than one type may be specified in a comma-separated list. The list of filesystem types can be pre- fixed with no to indicate that no action should be taken for all of the mentioned types. Note that umount reads information about mounted filesystems from kernel (/proc/mounts) and filesystem names may be different than filesystem names used in the /etc/fstab (e.g. "nfs4" vs. "nfs"). -v, --verbose Verbose mode. -V, --version Display version information and exit. -h, --help Display help text and exit. LOOP DEVICE The umount command will automatically detach loop device previously initialized by mount(8) command independently of /etc/mtab. In this case the device is initialized with "autoclear" flag (see los- etup(8) output for more details), otherwise it's necessary to use the option --detach-loop or call losetup -d <device>. The autoclear fea- ture is supported since Linux 2.6.25. EXTERNAL HELPERS The syntax of external unmount helpers is: umount.suffix {directory|device} [-flnrv] [-N namespace] [-t type.subtype] where suffix is the filesystem type (or the value from a uhelper= or helper= marker in the mtab file). The -t option can be used for filesystems that have subtype support. For example: umount.fuse -t fuse.sshfs A uhelper=something marker (unprivileged helper) can appear in the /etc/mtab file when ordinary users need to be able to unmount a mount- point that is not defined in /etc/fstab (for example for a device that was mounted by udisks(1)). A helper=type marker in the mtab file will redirect all unmount re- quests to the /sbin/umount.type helper independently of UID. Note that /etc/mtab is currently deprecated and helper= and another userspace mount options are maintained by libmount. FILES /etc/mtab table of mounted filesystems (deprecated and usually replaced by symlink to /proc/mounts) /etc/fstab table of known filesystems /proc/self/mountinfo table of mounted filesystems generated by kernel. ENVIRONMENT LIBMOUNT_FSTAB=<path> overrides the default location of the fstab file (ignored for suid) LIBMOUNT_MTAB=<path> overrides the default location of the mtab file (ignored for suid) LIBMOUNT_DEBUG=all enables libmount debug output SEE ALSO umount(2), losetup(8), mount(8) HISTORY A umount command appeared in Version 6 AT&T UNIX. AVAILABILITY The umount command is part of the util-linux package and is available from Linux Kernel Archive <https://www.kernel.org/pub/linux/utils/util- linux/>. util-linux July 2014 UMOUNT(8)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | LOOP DEVICE | EXTERNAL HELPERS | FILES | ENVIRONMENT | SEE ALSO | HISTORY | AVAILABILITY